Rilasciato Hekate – CTCaer Mod V4.8 Con Supporto Completo Del Firmware 7.0.0/7.0.1

It supports both FAT32 and exFAT.

Folders and Bootloader files

Folder / file Description
boot loader Main folder.
| __ bootlogo.bmp It is used when customization is active and no logopath was found. It can be skipped.
| __ hekate_ipl.ini Main configuration of the bootloader and startup entries.
| __ update.bin If more recent, it is loaded on startup. For modchips. It can be skipped.
bootloader / ini / For individuals. ‘More configurations …’. Autoboot is supported.
bootloader / sys / For system modules.
| __ libsys_lp0.bso LP0 (sleep mode) module. Important!
bootloader / payloads / For useful loads. Menu ‘Payloads’. Autoboot supported only by including them in an ini. All bootloaders, tools, and Linux payloads from CFW are supported.
bootloader / libtools / Future reserved

Configuring the bootloader

The bootloader can be configured via ‘bootloader / hekate_ipl.ini’ (if present on the SD card). Each ini section represents a boot entry, except for the special ‘config’ section that controls the global configuration.

There are four possible types of entries. ”  []  “: Boot entry, ”  {}  “: Caption, ”  #  “: Comment, ”  newline  “: .ini newline cosmetic.

Keys / configuration values ​​when the boot entry is  config :

Configuration option Description
autoboot = 0 0: Disable, #: number of the boot entry to start automatically.
bootwait = 3 0: Disable (Disable bootlogo also.) To have  VOL-  pressed since the injection goes to the menu.), #: Wait time for  VOL-  to access the menu.
customlogo = 0 0: use default hekate bootlogo, 1: use bootlogo.bmp.
verification = 2 0: Disable backup / restore verification, 1: Sparse (block based, fast and not 100% reliable), 2: complete (based on sha256, slow and 100% reliable).
autohosoff = 1 0: Disable, 1: If you wake up from HOS via an RTC alarm, show the logo, then turn off completely, 2: No logo, turn off immediately.
backlighting = 100 Screen backlight level. 0-255.

Possible combinations of boot entry keys / values:

Configuration option Description
logopath = {path SD} If global customlogo is 1 and empty logopath, bootlogo.bmp will be used. If logopath exists, it will load the specified bitmap.
warmboot = {SD path} Replaces the warmboot binary file
secmon = {SD path} Replaces the safety monitor track
kernel = {SD path} Replaces the kernel binary file
kip1 = {SD path} Replaces / adds the initial kernel process. More can be set.
kip1 = {SD folder} / * Upload each .kip / .kip1 to a folder. Compatible with single Kip1 keys.
kip1patch = patch name Enable a kip1 patch. Specify with multiple lines and / or as CSV. The patches implemented now are nosigchk, nogc
fullsvcperm = 1 Disable SVC verification (complete authorization for services)
DebugMode = 1 Enable debug mode
1 atmosphere = Enable the application of Atmosphère
payload = {SD path} Launch of the payload. Tools, Linux, CFW bootloader, etc.

Changelog

V4.8

  • Full support 7.0.0 / 7.0.1  . 
    The keys are generated through the thirst of Atmosphère.
  • In addition, sept / payload.bin, if it is found to be hekate, is updated via update.bin.
  • Restarting in a boot entry selected via HOS hb
    You can now force a boot configuration on hekate by setting the boot memory to the hekate track. 
    This can be done via a homebrew, which sets the entry ini that you want to start. 
    In addition, it is also possible to perform a forced start on the menu. Please check readme.md
  • Automatic NoGC
    Monitors fuses and automatically applies the patch if the firmware is higher. 
    It is now a global configuration and set to Auto by default. (0: deactivated, 1: automatic)
  • Fixed a bug with the ini list, where it crashed when using wildcard * with  kip1=.
  • The quality of life is resolved under the hood, which facilitates the user’s life.
  • As always, many bug fixes and some refactoring.

V4.6

  • Fixed the problem of sleep for declassed units with efuses burned more than necessary  .
  • Fixed the problem with the chainloading of update.bin  and forced hw init to update, in case you change again in the future. 
    This is a   quick solution and requires you to have v4.6 on your modchip / dongle.
  • New archive bit correction
    Now you can also repair the Nintendo folder. No more “corrupted” sds when updating the SD card or restoring the Nintendo folder.
  • Fixed the problem of printing UART debugging  . Thanks  @ hyln9
  • Automatic HOS power is now disabled by default. Probably, many people have learned what it does and can activate it from the Options menu.
  • Some small SMMU emulations for TSEC fixes for the most unfortunate out there. The maximum waiting time remains low.
  • Many many fixes and even added some error messages for recovery and boot options.

V4.5

This release supports the launch of all current OS / CS CFWs, Linux chainloading and payload tools. 
No more SD card removals

Last OFW supported:  6.2.0

News in this version

  • Full support for 6.2.0  . Many  thanks to  @nwert  and  @ balika011  for their help! 
    –  Supports Secure Monitor and new Exosphere
    –  Supports booting 6.2.0 with less than 8 fuses
    –  It has a  100%successful relationship
    -Added support for the tools “Print TSEC keys” and “Dump pkg1 / 2”
  • Fixed the problem with YouTube HDCP  . Thank  @hexkyz  for having  devoted  some time to investigate.
  • Each file lister now ignores hidden files and .dot files. Thanks  @StevenMattera
  • The Minerva Training Cell library for hekate has been updated to the latest version (v1.1)
  • Added the “silent option to the HOS Auto-Off option. Now you can choose if you want the logo to be shown. Thanks  @Huntereb
  • Refactored the main.c to the simpler grouped sections. Furthermore, hos.c has taken some love.
  • Many many bugfixes

NOTE:  Everything related to hekate has been moved to the bootloader folder   .

Download

Source and credits
Github

Trả lời

Email của bạn sẽ không được hiển thị công khai. Các trường bắt buộc được đánh dấu *